ICOM A2 Network Connection Setup User Manual

This is all about network connection (wired or wireless) setup for ICOM A2 diagnosis with ISTA+ or programming with ISTA/P. All situations you may encounter are solved here.

*****Part 1 Wired connection when ISTA-P programming
it’s better to use Lan cable to connect to network instead of wifi, for wifi is not stable sometime and cannot start programs ISTA-P (ISS-NEXT)
1

how to connect to network via Lan cable?
method 1: PC – router – ICOM
connect PC to the router, then connect ICOM to router
method 2: ICOM – PC
Directly connect ICOM emulator to PC
*****Part 2 Wireless/WiFi connection when ISTA+ diagnostics
you can use wifi during diagnosis with ISTA+. but sometimes, the connection will be cut off automatically and program prompts you to continue connection

Wlan settings
go to ICOM Configuration Manger, and select Wlan settings-> Security type:WPA2 personal. the password should be the same with that of router. then save data and unplug and re-plug the Lan cable to connect to icom. it is impossible to diagnose via wifi if password is not set
(NOTE: this is not for USB WiFi; USB wifi comes with password and router setup)
11

what to do if WIFI fails to connect?
1.go to VCI settings, then select “HO-ICOM/NET”, NOT Ediabas
2.open Itool Radar to change ICOM IP address
3.find out IP address: 192.169.68.119
4.then go to “Confort Module” to change ip

ATTENTION:
how to solve “Reserved”
during diagnosis, if the state is “Reserved”, it means the program is occupied. to exit the program illegally should be remain Reserved and cannot go to diagnostics.

when you meet with “Reserved”, please unplug the ICOM mux or close at Easyconnect, then “Reserved” turn to be “Free”.

go to Easyconnect Utility to set IP address: 192.169.68.119, Mode: DiagBus, then click “ICOM Lock” and “Check” to check the battery voltage and ignition

how to solve “Firmware”
if the state displays “Firmware”, it means the ICOM firmware need to be updated
Steps to update China ICOM firmware:
1). Use your cable and connect ICOM to port
2). Power ICOM by 12V power adapter or from 1x DLC
3). Use your browser (IE) and browse 169.254.92.38:60080/
User name: root
Password: NZY11502
4). Click “Update Firmware”,and you can find the version of firmware.
5). Select ICOM-BootImage-XX-XX-XX.bin, set image type to “SYSTEM”, click “Send the file”
6). When it will say “Write the image file to the flash?”, click “Yes”, then the ICOM led it will been RED
7). When it will say “The SYSTEM IMAGE update was successful”, click “Update Firmware”
8). Select ICOM-Application Image-XX-XX-XX.bin, set image type to “APPLICATION”, click “Send the file”,the file is big so it will take some minutes to finish have patience.
9). When it will say “Write the image file to the flash?”, click “Yes”, then the ICOM led it will been RED again
10). When it is ok, click “reboot”. 

Related Posts
BMW ICOM firmware to V1.40 steps: 1.Download BMW ICOM V1.40 firmware update file 2. Please connect BMW ICOM A2 with computer using internet cable, power ICOM by 12V power adapter or from ...
READ MORE
New V2015.12 ICOM Software List and Functions
ESobdii.com comes the newest version BMW ICOM software HDD Software version: ISTA-D:3.56.1002 ISTA-P: 3.57.2.002 VIN: 2015.10.14 Not connected 9000 days remaining System Requirements: Windows 8 Dual-core processor, better above I3; over 4G of memory Support Model: Lenovo ThinkPad: T61, T410, ...
READ MORE
BMW ICOM A3 advantages
ESobdii.com  comes the newest BMW ICOM3, here's the details: BMW ICOM A3 advantages compared old ICOM A2: -Newest FW: V1.37 -BMW ICOM A3 for vehicles with OBD access receives a significantly more powerful ...
READ MORE
2015 BMW ICOM WIFI wireless connection steps
2015 BMW ICOM WIFI wireless connection steps: Computer requirement:Almost 95% laptops on the world with Intel chip (I3/I5/I7 series) and have 4GB memory 1. Insert WIFI USB D-link into the computer via ...
READ MORE
How to update BMW ICOM firmware to V1.40?
New V2015.12 ICOM Software List and Functions
BMW ICOM A3 advantages
2015 BMW ICOM WIFI wireless connection steps